1S HD 75mm Micro Whoop FPV Racing Drone ELRS BNF w/ 0802 20000KV Motor RunCam Split3-Lite 1080P Camera DVR

Introduction: 
HD version is a light and efficiency 75mm brushless whoop which provide 1080P HD video record function. A highly integrated AIO FlightController, supports ESC with a maximum current output of 12A. We added blackbox for this 1s 75mm HD recorder whoop. Now it could support gyroflow. Although the external blackbox is not install perfectly and insert SD card is not friendly to most of the people, however we still think it's really excited for this small whoop could record a video with gyroflow steady and keep safe flying. 

Features: 
X12 5-IN-1 AIO flight controller. 
VTX Power up to 400mw. 
ELRS V2.0 Support. 
NEW RS0802 KV20000 motors. 
1080P HD Video record. 
Blackbox Ready support GYROFLOW. 
Smooth and powerful. 
Compatible for 1S Lipo/LIHV. 
Recommend 1S 450mah/550mah/650mah batteries (Not include). 

Specifications: 
Item Name: Mobula7 1S HD 75mm Micro FPV whoop drone; 
Wheelbase: 75mm; 
Size: 99mm*99mm*45.5mm; 
Weight: 33g; 
Receiver option: SPI 2.4GHz ELRS V2.0 / SPI Frsky D8/D16. 

Motor: 
Mode: RS0802 KV20000; 
Configu-ration: 9N12P; 
Stator Diamter: 8mm; 
Stator Length: 2mm; 
Shaft Diameter: Φ1.5mm; 
Motor Dimension(Dia.*Len): Φ10.5mm*13.5mm; 
Weight(g): 2.0g; 
No.of Cells(Lipo): 1S only. 
Propeller:  Weight: 0.24g; 
Material: PC; 
Pitch: 1 inch; 
Props Dia: 40mm; 
Center Thickness: 5mm; 
Center Hole Dia: 1.5mm. 

Flight Controller: 
X12 ELRS V2.0 flight controller built-in ELRS 2.4G receiver Target: CRAZYBEEF4SX1280; 
X12 Frsky V1.0 flight controller built-in SPI Frsky 2.4G receiver Target: CRAZYBEEF4FR; 
MCU: STM32F411CEU6 (100MHZ, 512K FLASH); 
Sensor: ICM20689(SPI connection); 
Mount hole size: 25.5mm*25.5mm; 
Power supply: 1S battery input (DC 2.9V-4.35V); 
Built-in 12A(each) Blheli_S 4in1 ESC; 
Built-in Betaflight OSD(SPI Control); 
Built-in 5.8G OpenVTX 0mw~400mw; 
Built-in ExpressLRS 2.4G,Frsky D8/D16; 
Built-in voltage detection; 
Built-in current sensor. 

Onboard 4in1 ESC: 
Power supply: 1S LiPo/LiPo HV; 
Current: 12A continuous peak 15A (3 seconds); 
Support BLHeliSuite programmable; 
Factory firmware: Z_H_30_REV16_7.HEX; 
Default protocol: DSHOT300; 
Support Bluejay firmware; 
When use Blujay firmware with 48khz, should set startup power to 1100/1200. 

Onboard SPI ExpressLRS 2.4GHz Receiver: 
Packet Rate option: 50Hz/150Hz/250Hz/500Hz; 
ExpressLRS Firmware version: V2.0; 
RF Frequency: 2.4GHz; 
Antenna : Enameled copper wire length 30mm; 
Telemetry output Power: <12dBm; 
Receiver protocol: SPI ExpressLRS; 
Compatible with ExpressLRS V2.0 TX Module; 
Couldn't flash separately ExpressLRS firmware. 

Onboard Frsky SPI D8/D16 receiver Version: 
Packet Rate option: 50Hz/150Hz/250Hz/500Hz; 
ExpressLRS Firmware version: V2.0; 
RF Frequency: 2.4GHz; 
Antenna : Enameled copper wire length 30mm; 
Telemetry output Power: <12dBm; 
Receiver protocol: SPI ExpressLRS; 
Compatible with ExpressLRS V2.0 TX Module; 
Couldn't flash separately ExpressLRS firmware. 

Onboard 5.8g OPENVTX: 
Firmware version: OPENVTX; 
Smartaudio v2.1; 
PIT Mode support; 
RCE Mode support; 
Channels:48ch; 
Transmitting Power: 0/RCE/25mw/100mw/400mw; 
Power supply: DC 5V; 
Current (5v): <650ma (400mw). 

Runcam Split3-Lite: 
Model: RunCam Split3-Lite; 
Field of View(FOV): Recording FOV 165°(FPV FOV: 165 ° @16:9, 130 ° @4:3); 
Video Resolution: 1080@60fps/1080@50fps/1080@30fps/720@60fps; 
Video File Format: MOV; 
Image Resolution: 2 MP; 
TV Mode: NTSC (720*480)/PAL (720*576) Switchable; 
Interface: JST 1.25mm / UART and SH 1.0mm; 
Max Micro SD Card Supported 64G(need Class 6 or above, recommend Class 10/UHS-I/UHS-II/UHS-III); 
Hole Distance of Installation: 25.5*25.5mm; 
PCB Size: 29*29mm; 
Lens Module Size: 14*14mm; 
Lens Specs: M9; 
Power Input: DC 5-20V(Non-direct power supply from battery. Powered directly with battery will generate surges and burn the camera.); 
Working Current: 450mA @5V. 

External Blackbox: 
Size: 18*15.5*4.5; 
With Built-in Voltage booster module; 
Weight: 1.5gram; 
SD Card support max to 32GB; 
SD Card need to use FAT32 Format; 
Notes: Need to careful to insert the TF SD Card , and don't pull it out while install the battery. 

Package Included: 
1x 75mm whoop Drone Frame (Mobula7 v4 frame); 
1x Flight Controller AIO ESC Receiver vtx; 
4x RS0802 KV20000 Brushless Motor; 
2x Gemfan 1610-2 bi-blade propellers CW; 
2x Gemfan 1610-2 bi-blade propellers CCW; 
1x Runcam Split3-Lite Camera; 
1x External Blackbox Module support gyroflow; 
1x Propeller Disassemble tool; 
1x Balance charging board.